16 Simple Bypass Valve-manufacture,factory,supplier from China

Commands for use: Mainly used for capillary head give up manage (the right give up of the pull ring is hooked up to a 16mm drip tape, that is fixed through the pull ring; the left give up is hooked up to the water shipping most important pipe, which may be used for pe pipes (wall thickness more than 1mm), water transport tape or use with matching rubber bands , connect to pvc pipe.)Product introduction: the pull-ring pass switch is a generally used drip irrigation transfer.

This product is used when the drip irrigation system uses tape as the main pipeline. The branch water source, the main pipeline (soft belt) is connected with the drip irrigation belt, so that the water in the main pipeline (soft belt) flows into the drip irrigation belt separately.Use a punching machine (diameter 14mm) to make holes on the side of the soft water belt, then screw the tee into the hole of the soft water belt, tighten the nut to fix the bypass on the soft water belt, and connect the soft water belt to the other side of the drip irrigation belt.

Fertilization flow of three-channel fertilizer applicator:1. First of all, the dissolved fertilizer solution into the fertilizer pot, open the main pump, through the regulating valve will be filled with water, closed water injection valve (the process of irrigation valve can always open) . When fertilizing, the “Time knob”in the control cabinet is used to adjust the time of fertilizing, the pump starts, the fertilizer in the tank is pumped into the main pipeline water by the pump, and the fertilizing is finished at the same time.

In recent years, there are a variety of popular orchard irrigation methods, such as immersion irrigation, manual irrigation, water-saving irrigation, high-level sprinkler irrigation, and simple sprinkler irrigation. However, these technologies all have their shortcomings more or less. The cost of immersion irrigation is high, and the cost of manual irrigation is high. The effect is relatively poor. Water-saving water-saving irrigation has low one-time investment, high water-saving efficiency, simple maintenance in the later stage, and high-level sprinkler irrigation.

Setting up a drip irrigation system can be daunting — there are so many products to choose from, and often hardware stores carry whacky supplies. First and foremost, don’t buy a soaker hose! A soaker hose is notorious for uneven watering, it breaks down quickly, and is a hassle to repair. There are far superior products that are cheaper, last longer, and are simple to repair. In short, there are three different drip products to use, depending on your application:• Half-inch emitter tubing.

1. Establish a drip irrigation system first. The length and depth of the pipeline system should be designed according to basic conditions such as topography, soil texture, crop planting conditions, and water sources. So that the integration of water and fertilizer can play the greatest efficiency.2. The fertilization system should be designed for quantitative fertilization in the field, including the location, capacity, outlet, fertilization pipeline, distributor valve, water pump and fertilizer pump of the reservoir and fertilizer pool.3.

When the filter is working normally, the pressurized water flows into the tank from the water inlet and reaches the filter layer evenly. When the water flows through the filter layer, the impurities are filtered and retained. There is a water trap with a valve at the bottom of the filter, and the filtered water is collected evenly and then flows out of the filtering equipment.With the continuous accumulation of impurities in the filter layer, the water flow loss continues to increase.

Pressure CompensationThe amount of pressure that flows through a drip irrigation system can fluctuate, depending on hose length and garden bed elevation, among other factors. This can cause emitters to flow differently than designed, with more or less water flow depending on pressure.To combat this, the best drip irrigation system emitters are pressure compensating by design. They’ll emit the same amount of water regardless of the pressure at their inlet (where they attach to the main hose).

The arrangement and installation of the dripping belt: The branch pipes are arranged according to the row direction of grape planting. Generally, the branch pipe is arranged in the middle of the grape row, and the dripping belt is arranged according to the spacing of the grapes. If the planting row is too long, it can be divided into two groups from the middle part of the vineyard, and two valves can be installed to send the water to both sides respectively to implement group irrigation.Precautions for drip irrigation1. Prevent the drip hole from clogging.

Compared with the dripper, the most obvious feature of the pressure-compensated dripper is:1. The pressure compensation dripper can make the elastic silicone sheet change the section of the water outlet with the help of water conservancy pressure, automatically adjust the flow rate, and make the water output uniform;2. The pressure compensation performance is strong, and the automatic control water dispenser is the best choice. It is especially suitable for undulating terrain, unbalanced system pressure and need to increase capillary.How to choose a pressure compensation dripper?1.

Based on the definition and connotation of the above-mentioned water-saving products, it can be divided into the following categories from the principles and approaches of water-saving:(1) Products that directly improve the use efficiency of water resourcesIt is a water-consumable product, and it can reduce water consumption compared to similar products under the condition of fulfilling the same function.(2) Products that reduce the loss of water resources and prevent pollutionIn the process of use, it does not consume water resources, but it can ensure that water resources are not lost and po

1. AdvantagesSave water, fertilizer and laborDrip irrigation is a full pipeline water delivery and local micro-irrigation, which reduces the leakage and loss of water to the lowest limit. At the same time, because it can supply the water required by the crop root zone in a timely manner, there is no problem of peripheral water loss, and the water use efficiency is greatly improved. Irrigation can be conveniently combined with fertilization, that is, dissolve the chemical fertilizer and pour it into the irrigation system.